School Zone Santa .Com

 Down Blakehurst way on King Georges road new High -Vis yellow clearway signs were put up in June this year, replacing the old white ones.

I first saw these new ones two weeks after they were put up. (as explained in this previous post below.)

  http://www.schoolzonesanta.com/index.php/is-it-finished    ( Please copy and paste the link as I can't get it to go right)

Hi-Vis yellow ones were put up in July 2015, and ever since I have by phone email first to the then Road Minister Gay

Dear Minister Gay,

I recently  saw you on TV and you mentioned the new clearway times and the new signage between Blakehurst and Sutherland. The new clearway times have made a difference to traffic flow,

but the Hi-Vis yellow clearway signs I'm afraid  are an eyesore, and to make matters worse the majority are now adopting jaunty angles. The signs are attached to a bracket with 2 bolts but the bracket is fastened to the power pole or its own metal pole with one bolt, so if the sign isn't tightened  correctly, it can  pivot on the single bolt as can be seen in my photos.

There are  old white clearway  I've seen, also at angles,  and are also  fastened  with one bolt. A rethink in the fastening department is warranted.  The bracket used now is over engineering and might have been good enough for the DMR and RTA but common sense is required in this age of innovation

What is wrong with a Tech screw, top and bottom of the sign, fastened to the power pole using an  18 volt impact screw driver.

  In the big scheme of things this is small potatoes,   but 5 klms of  these gaudy bright yellow (near new) clearway signs at crazy angles advertise ( in Hi Vis) for all to see , RMS incompetence. 

Please get someone from the relevant department  to have a look and get the job done right.

Last Sunday I drove to Church Point and noticed new Hi-Vis yellow clearway signs on Mona Vale through the West Ryde /Top Ryde area, that weren't there Boxing day. And some of these signs are already adopting less than professional angles.

Regards

Hans Stephens

and I emailed my local MP  and then the NSW premier

Title: Mr
First Name: hans
Last Name: stephens
Street address: 
Suburb: Kirrawee
State: NSW
Postcode: 2232
Phone: 040
Email: stephens1510@optusnet.com.au
Type of enquiry: Message
Subject: This is not spam, please take seriously
Message:
Dear email sorter,
I did email the new roads minister, no reply
I did email my local Member
(whom I voted for)
= A................................................................................
Dear Mr Evans,
I sent an email to my old MP, Mr Kerr, and his office said my email would be forwarded onto you.
As I haven't had a reply from you to my RMS concerns, I will repeat them. The RMS is renewing old white clearway signs with new Hi­Vis yellow
ones
My website www.schoolzonesanta.com explains it all, with photos of clearly incompetent installation of the new signs using rubbish brackets,
which didn't work with the old white signs either. I have emailed the new roads minister weeks ago, with no response.
All that needs to be done is for someone to take charge, scrap the old brackets, and use a bit of common sense, and two screws as shown in one
of my photos. Hope you can help, before they go right through NSW changing signs at great unnecessary expense to the taxpayer.
Regards Hans Stephens
= A.............................................................................................
MP Lee Evans emailed me yesterday, and said "he is also waiting for replies."
So here I am. I'm sure the Premier has more to worry about than crooked signs, but there must be time to email
or phone someone at the RMS to use a bit of common sense, and stop wasting money on this, at least.
Alan Jones years ago was on about an upcoming election and I rang him. "I don't care who gets in" I said.
"Oh you must care" said he.
" No I don't care, I said, as long as they don't waste the money"
I tried to upload more photos (too big), but there are plenty on www.schoolzonesanta.com
Thankyou for your time
I would like a response: Yes, I would like a response
I would like to receive regular updates from the NSW Government: Yes
End of messag

 This is the letter I mailed to Ms Pavey.

The Hon. Melinda Pavey, MP
37 Elbow Street
WEST KEMPSEY NSW 2440

Dear Minister Pavey,
This letter should not have been necessary as I have, in the past, raised this problem with my local member, with the
Premier's Office and with your office, but as these efforts have not yet yielded a satisfactory outcome, I thought I should
write to you again.
The RMS is renewing the old white clearway signs on major roads with new HI- Vis yellow ones.
The old brackets used to hold up the white signs didn?t work, and they don?t work on the new yellow signs either.
My website www.schoolzonesanta.com has many photos showing examples and explaining the problem.
Something has to be done before the new yellow signs are completely rolled out across NSW.
Please spend a couple of minutes to have a look at my site and have someone, with the necessary authority, investigate
and fix this very simple problem.
I've provided here an example of the old white clearway signs, these being on Roberts Road, Greenacre, and, as you
can see, the mounting system on the white signs was totally unsatisfactory.
This folly is being repeated when the white signs are being replaced with Hi-Vis yellow signs by contractors engaged by
the RMS.
Many more examples can be found on www.schoolzonesanta.com.
I think that you would agree that this level of incompetence is simply unacceptable and that it points to a deeper problem
within the administration of the RMS.
These signs provide "hi-vis" advertising of RMS incompetence and, by extension, discredit your Government.
As I'm retired, I would like to offer my services as a consultant, at no cost to the taxpayer, in order to rectify this
unsatisfactory state of affairs in the most cost effective manner.
Thank you for your time.
Yours faithfully,

and even a stamped letter to the roads Minister Ms Pavey and every new section of replaced clearway signs have examples that look like these two below:

   This photo of those two "new signs" used many times on many previous posts, was taken 6 months after installation in Gymea, and started me on this mission.

 I thought the first email would fix the obvious problem, but how wrong I was.

 Obviousily the RMS needs help.

This is a simple guide on how to put a RMS clearway sign on an overseas owned power pole, 

  Step  one                   After of course first taking the proper safety precautions,  unbolt the RMS Hi-Vis yellow clearway  sign from it's RMS bracket.

Step Two                               bolt the RMS bracket that now has an extra hole, back onto the pole 

  Step three                                          make sure the RMS bracket is on the leval

  Step three                                                    put in the extra coach bolt

Step four           Refasten the Hi-Vis yellow RMS clearway sign back onto the RMS bracket, and the job's done. 

Before the Sydney Harbour Bridge was opened, to prove that the bridge was strong enough,

most of Sydney's railway locomotives were rolled out onto the bridge, the bridge survived and

to prove that 2 two fixing points on a clearway sign bracket can hold up a little aluminion sign, I hung 28lbs of weights onto the sign, and it didn't move

 leval

                                                                                                                                              What more can I say?   

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

Anyone looking back on the nearly four years of pages on this site

can understand my angst.

I've said all along that this is an embarressment, and a waste of money 

Incompentece in Hi-Vis but would anyone listen?

Just ignore him, and he will give up and go away.

..................................................................................

 No I won't